|
09-21-2015, 01:16 PM
|
#1
|
Junior Member
Join Date: Sep 2015
Location: Owosso
Posts: 3
|
Pop up bed collapsed
I own a 2000 Manistee Heritage. We love it for a 1st venture into campers. On Labor Day weekend our rear bed collapsed as we were sleeping on it in the middle of the night. The support brace bent which caused the failure. The bed is rated at 1100 lbs and combined weight we are around 450 lbs.
Has anyone else had this issue. I am currently waiting to hear back from my dealer on how much parts are going to cost to get us camping again. I am also looking for ways to add support to the bed as a precaution going forward so my wife will sleep on it again.
|
|
|
09-21-2015, 01:56 PM
|
#2
|
Senior Member
Join Date: Mar 2015
Location: Abingdon
Posts: 6,177
|
Holy...!!!!
__________________
2013 Jayco Eagle 328 RLTS
2021 Keystone Montana 3121RL
2013 F350 6.7L 4x4 CCLB
W/Air Lift air bags (front & rear)
Equal-I-Zer™ WDH & B&W Companion
|
|
|
09-21-2015, 02:04 PM
|
#3
|
Senior Member
Join Date: May 2015
Location: Campbell Hall
Posts: 2,835
|
Just to sound the voice of pessimism;
It may not be worth it to repair your pop-up.
For close to the same money, you could get yourself into a 2009 or 2010.
The suspensions (drawer glide-like assemblies) are often riveted to the fiberglass tub. Your photo only shows a bent suspension on the side near the camera. I can't tell the damage on the other side. At the very least both suspensions will have to be replaced. And that can only happen if the plywood bed is still reasonably intact and, more importantly, the tub hasn't been torn.
__________________
TT 2015 19RD "TheJayco"
TV 2003 F-350 "Montblanc" - Housebroken chore truck
Sitting in The Cheap Seats.
And proud of it!
|
|
|
09-21-2015, 02:46 PM
|
#4
|
Junior Member
Join Date: Sep 2015
Location: Owosso
Posts: 3
|
Right now it"s looking like mainly the bed slides, one side of aluminum bed frame, one support, rollers and the bolts that attached the rollers to bed slides. 5 of the 6 bed slide roller bolts sheared which probably saved my pop up frame. We were able to unbolt bed slides from pop up frame. So far, it looks like the only part jayco does not have available is the support piece which caused the issue. Fortunately the velcro pulled away from the bed frame without tearing.
|
|
|
09-21-2015, 02:58 PM
|
#5
|
Senior Member
Join Date: May 2013
Location: SE Wisconsin
Posts: 3,431
|
Yikes! I hope no one was hurt!
__________________
Chuck
2013 Jayco Jayfeather X20 E (sold)
2016 Chevy Silverado LTZ 2 Z71 Crew Cab (sold, and dearly missed)
|
|
|
09-21-2015, 03:00 PM
|
#6
|
Junior Member
Join Date: Sep 2015
Location: Owosso
Posts: 3
|
I was pretty sore for the next couple days but nothing serious.
|
|
|
09-21-2015, 03:27 PM
|
#7
|
Senior Member
Join Date: Jan 2014
Location: Plano, Texas
Posts: 507
|
I am so sorry for what happened to you, but all I could do was think of an old Laurel and Hardy or 3 Stooges moment.. We had a popup and I can imagine me and the DW falling out and the weight shifting and my two boys on the other side flying around in their bunk. And God only knows what would have happened to the dog...
We actually forgot to put the suspension tubes in on the boys side one time. They almost fell out.. Fortunately no body got hurt...
Glad that you weren't hurt
__________________
2013 Jayco Jayflight Swift 264BH
2002 Yukon 5.3L Vortex w/tow package
When I die, I want to go peacefully like my grandfather did–in his sleep. Not yelling and screaming like the passengers in his car.
|
|
|
09-22-2015, 08:03 AM
|
#8
|
Senior Member
Join Date: Apr 2013
Posts: 517
|
Not that you asked...
The picture of the failed support looks like it has a bow in it that may have been there previously? If the support had even a slight curve before the accident, that would explain why it failed. The supports are under compression so the forces need to remain in column.
After seeing your failure I'm going to inspect my supports to be certain they are completely straight.
Other than the extra weight, a stiffener can easily be added by clamping proper sized angle iron or aluminum angle to the OEM supports using worm drive hose clamps or possibly use stainless steel picture wire wrap to marry the parts. At minimum, clamp the angle using a clamp at each end and one approximately in the center. Actually filament packing tape would be easy and strong enough as long as it is replaced if it shows signs of wear.
The closer you get to the ends the less the additional support is needed. As is shown by your bent support, the stress gets more critical in the center.
It would be a shame to scrap out a good trailer for lack of replacement parts. I haven't seen the damage. A good metal fabricator may be able to straighten the bent rails or copy the shapes for replacement if it turns out parts are not around. The originals are likely aluminum. There is no reason except possible higher weight that the copies can't be galvanized steel.
Quote:
Originally Posted by thezems
... So far, it looks like the only part jayco does not have available is the support piece which caused the issue. ....
|
A couple of our 2001 galvanized bed supports have a bit of surface rust. Should the paint I put on them not last my plan is to fabricate new supports using 1/2" EMT electrical conduit tubing. I haven't specifically checked to compare the strength, but it looks to be similar and will be strong enough.
Another option would be to use 3/8" schedule 40 galvanized pipe. The 3/8" pipe will be overkill and heavy, but may help your wife to feel more confident.
The 3/8" pipe cannot be just flattened like the OEM to form the tab ends to fit into the receivers. The pipe end cross sections could be cut to form the tab. Once the tab size is cut it will be easy to form the tab to fit into the receivers. The single tab made from the schedule 40 pipe wall will be plenty strong. Some pipe wall curve can even be left in the tab. It doesn't need to be pounded completely flat as long as it fits into the receivers.
Added.
My method would be to copy the OEM supports leaving the end tabs a bit long. That way after they are formed, the tabs can be cut to length for a more exact fit. That should make fabrication/copying a bit easier.
Good luck. vic
|
|
|
09-22-2015, 05:57 PM
|
#9
|
Senior Member
Join Date: Apr 2013
Posts: 517
|
I did some inspection and comparison EMT conduit vs the OEM bed supports on my 2001 Kiwi 23b.
The 1/2 EMT conduit is very slightly smaller in diameter, but has a heavier wall thickness than the OEM tube supports. It was easy to flatten the ends in a bench vise to copy the tabs. The 1/2" EMT flattened ends fit both the receiver at the bottom and the one on the bed door (upper end) very well.
Given the heavier wall thickness I would use 1/2" EMT for replacement bed supports without a second thought. After experiencing the failure your perception and situation may differ.
3/4" EMT conduit is a good choice too. It is substantially larger in diameter than my OEM supports and also has a thicker wall. I crushed the end of a piece to make a tab. The flattened tab 3/4" EMT fit the top receiver on my 23b just fine. The bottom receiver was just a bit too small. Trimming the conduit tab on one side by 1/8", maybe 3/16" would allow the 3/4" EMT tab to fit my A frame and rear bumper receivers. The trimming could be accomplished with a hacksaw, angle grinder, or with more effort a flat file.
Having a different size tab on each end would make the supports only fit one way, but that should be workable.
Anyone with a decent sized bench vise and typical hand tools can copy the OEM supports using EMT conduit. The tabs could even be fabricated using a hammer. Electrical standards set conduit at 10 ft lengths. A 10 ft length should yield 2 each supports.
FWIW. vic
|
|
|
09-22-2015, 06:33 PM
|
#10
|
Senior Member
Join Date: May 2014
Location: North Western West Virginia
Posts: 671
|
Could have been worse... ya could have been in bear country! :-)
__________________
The Logan's
2018 Jayco Alante 31v
Me, Dear Wife,
2 Bluetick Hounds
1 Newfoundland
1 Newfoundland / Black Lab Mix
1 Cairn Terrier
|
|
|
09-22-2015, 07:02 PM
|
#11
|
Senior Member
Join Date: Mar 2015
Location: State of Confusion
Posts: 5,014
|
Quote:
Originally Posted by The Logans
Could have been worse... ya could have been in bear country! :-)
|
...or in the country, bare!
__________________
Murff
2015 White Hawk 20MRB (It's last year)
2017 F150 2.7 Eco Boost 3.73 Gears
|
|
|
10-01-2015, 07:43 AM
|
#12
|
Senior Member
Join Date: Apr 2013
Posts: 517
|
Under the "No good deed goes unpunished" category.
We arrived at our campsite and attempted to deploy the bed ends. Only 3 bed supports!! Where the h*ll... oops. I took one into the garage to verify the EMT tubing fabrication. Guess where it still sits?
I can say for certain now that 1/2" EMT tubing from Lowes, a hammer, and Channelocks will allow you to copy a bed support for your pop-up or hybrid camper. About 2 bucks for the tubing.
vic
|
|
|
10-01-2015, 09:54 AM
|
#13
|
Senior Member
Join Date: May 2012
Location: Minnesota
Posts: 9,782
|
Ouch, I know your feelings, kinda. My brother and SIL, had the same issue with their PU, a few years ago, on the front, I think king size bed. My dad and I fixed it. my brother, as good of a guy as he is, could not tell you show you what a tool is. As I recall we had it fixed up in a single weekend, along with a number of other issues. Luckily the canvas was not damaged. I also do not recall buy much in the line of parts.
My guess from looking at the pictures. The support bar was dinged/dented at some point near where it failed.
|
|
|
10-01-2015, 12:34 PM
|
#14
|
Senior Member
Join Date: May 2015
Location: Campbell Hall
Posts: 2,835
|
Quote:
Originally Posted by VicS1950
Under the "No good deed goes unpunished" category.
We arrived at our campsite and attempted to deploy the bed ends. Only 3 bed supports!! Where the h*ll... oops. I took one into the garage to verify the EMT tubing fabrication. Guess where it still sits?
I can say for certain now that 1/2" EMT tubing from Lowes, a hammer, and Channelocks will allow you to copy a bed support for your pop-up or hybrid camper. About 2 bucks for the tubing.
vic
|
Good MacGyver!
Co-incidentally, I forgot to install the clips that secure the WDH latches on the tongue this past weekend. Two 1/4" chain repair links $1.49 each, channelocks, hammer (broke during the process) with the WDH shank as an anvil...
Found one of the originals after we got back.
I love doing field repairs, don't you?
__________________
TT 2015 19RD "TheJayco"
TV 2003 F-350 "Montblanc" - Housebroken chore truck
Sitting in The Cheap Seats.
And proud of it!
|
|
|
10-02-2015, 09:20 AM
|
#15
|
Senior Member
Join Date: Apr 2013
Posts: 517
|
Whenever I think that I'm under control, something happens to remind me what a delusion I am living.
Quote:
Originally Posted by mike837go
Good MacGyver!
Co-incidentally, I forgot to install the clips that secure the WDH latches on the tongue this past weekend. Two 1/4" chain repair links $1.49 each, channelocks, hammer (broke during the process) with the WDH shank as an anvil...
Found one of the originals after we got back.
I love doing field repairs, don't you?
|
That sounds like a good emergency repair for your parts. I used a large pair of Channelocks as an anvil for beating the EMT into submission.
I planned to pack a flip down shelf to adapt as a TV shelf in my 23b. It wasn't on any of my many lists so of course I forgot it. I used some parts from my van stock to rig up a hanger for our 22" wide TV.
The nylon cord goes thru some loops made from picture hanging wire. I always have some of that on hand. To make the loop secure I placed an overhand knot in the wire before I finished with a twist. A simple twist without the knot can sometimes unwind.
I did need to add an extra string down from the door frame drywall screw to keep the TV from sliding off level.
It's working well enough that I plan to make it permanent. It even provides a bit of down facing angle to make better viewing.
My vision for the permanent install is use light cable with Nicropress loops. I'll use some hooks on the back of the TV for hanging, or possibly some flat sheetmetal formed into a hooked plate.
Obviously we won't travel with the TV hung, but we wouldn't do that with a shelf either.
vic
|
|
|
10-02-2015, 10:29 AM
|
#16
|
Senior Member
Join Date: May 2015
Location: Campbell Hall
Posts: 2,835
|
You beat an Emergency Medical Technician into submission?!?!
I always considered them kinda nice.
----------
Yeah, that setup for the television is great for viewing, but won't do well over potholes.
__________________
TT 2015 19RD "TheJayco"
TV 2003 F-350 "Montblanc" - Housebroken chore truck
Sitting in The Cheap Seats.
And proud of it!
|
|
|
10-02-2015, 12:28 PM
|
#17
|
Senior Member
Join Date: Jun 2012
Posts: 195
|
Did you check the bracket clip that it locks into on the bottom? When I bought my camper (a 2004 Jayco Feather) in 2011, one of the bolts had broken on one of the two clamps. I replaced the bolt, but if it was loose or broke, then you'd essentially have lost half of your support and I could see the remaining bar instantly bending under the pressure.
|
|
|
10-02-2015, 12:41 PM
|
#18
|
Senior Member
Join Date: May 2015
Location: Campbell Hall
Posts: 2,835
|
Quote:
Originally Posted by sirrealone
Did you check the bracket clip that it locks into on the bottom? When I bought my camper (a 2004 Jayco Feather) in 2011, one of the bolts had broken on one of the two clamps. I replaced the bolt, but if it was loose or broke, then you'd essentially have lost half of your support and I could see the remaining bar instantly bending under the pressure.
|
I installed the WDH myself. After an "uncomfortable" outing with a regular hitch. The clamps, chains and ball were brand-new. The bulk of the hitch was an auction 'win' because I was the only one to bid on it.
Yes, 1/2 the support went away when the clamp opened (tight turn heading to the gas pump and again when maneuvering into the campsite). But at foot-on-the-brake speeds, loosing that support was not all that noticeable.
I will say that I should upgrade the bars since I am running a 4 links under tension and the front end is still up about 1/2". That's a spring 2016 purchase if we still use the Taco. My F350 has been getting "interesting" of late...
__________________
TT 2015 19RD "TheJayco"
TV 2003 F-350 "Montblanc" - Housebroken chore truck
Sitting in The Cheap Seats.
And proud of it!
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|