Jayco RV Owners Forum
 


Reply
 
Thread Tools Display Modes
 
Old 09-07-2010, 09:04 AM   #1
leoslaton
Junior Member
 
Join Date: Aug 2010
Posts: 22
Skin damage repair question

2007 Jayflight, 28 RLS, single slide.

I have a bit of damage on the street side, rear just aft of the slide. It is not serious and I am trying to avoid taking it to the dealership (distance and money). I think I have attached a picture, may have screwed it up.
Anyway, it looks to be a fairly simple job of unscrewing the trim at the slide and at the corner and detaching the short panel.
I would appreciate hearing from anyone who has attempted a similar job and who will discuss traps and suppliers of aluminum and trim.
In the same vein, does anyone sell spray cans of Jayco color compatible paint?Thanks. Texas Slacker.
Attached Images
File Type: jpg 100_0725.jpg (85.5 KB, 80 views)
__________________

leoslaton is offline   Reply With Quote
Old 09-07-2010, 09:43 AM   #2
Denise
Momma Moderator
 
Denise's Avatar
 
Join Date: Jul 2009
Location: Back Home in the USA
Posts: 9,586
I've no experience with fixing damage to anything but would like to welcome you to the Jayco Owners Forum! Good luck with the fix and hope it turns out ok
__________________

__________________
MODERATOR

-Denise, DH, grandkids, and two rescue pups
-2009 Ford F-150 SuperCrew, 5.4L 3v 6speed, 3.73 limited slip, 18" LT rated tires, Max towing package
-2010 Jayco Jay Flight G2 29bhs

CLICK HERE to 30% $$ off your next Jayco RV
Denise is offline   Reply With Quote
Old 09-07-2010, 11:39 AM   #3
Texas Sam
Senior Member
 
Join Date: Aug 2009
Location: Austin, Texas
Posts: 235
You might find it easier to order the needed siding from Jayco to ensure that it is an exact color and pattern match to your trailer. Also, it looks like you will need to detach the lower section of the corner trim to get at the damaged end of the skin so you will need matching calk to reseal the corner trim after replacing the damaged skin.

I have not done this type of repair on a trailer but I have repaired aluminum siding on a relative's home. In that situation I had to remove all the sections from the bottom of the wall to the damaged section and then after installing a new section, reinstalling all the sections back to the bottom.

Good luck!
__________________
Sam
Emeritus Member of Jayco Owners' Forum
Texas Sam is offline   Reply With Quote
Old 09-08-2010, 08:03 PM   #4
Jaycojenni
Junior Member
 
Join Date: May 2010
Location: Saginaw, MI
Posts: 28
Our trailer is currently in the shop getting "body work" Our 29 bhs Jayflight G2 was hit with a bb or pellet earlier this year. They hit near the top of the slide out a few inches from the window. After calling our insurance and getting reminded that "if it is not much over the deductible better to not make the claim" I spoke with our dealer. The service writer laughed when i asked if it would be much over $250 to fix. He explained that RV's are sided from the top down (vs house siding bottom up). So that would mean all of the siding on our slideout would have to come off from the bottom up and be replaced and the window would have to come out etc......ended up $1,000. to fix. I would definitely research and gather lots of info on this repair because it may not be as straight forward as it seems
Jaycojenni is offline   Reply With Quote
Old 09-30-2010, 11:47 AM   #5
leoslaton
Junior Member
 
Join Date: Aug 2010
Posts: 22
I finally took pictures to a Jayco repair shop and got the same bad news. The shop foreman advised me to not even try. The trim at the slide can be removed only by removing the slide or "pushing it in a couple of inches'. I have no idea how to do this so will look into a body putty job. I still need a paint code but Jayco says they do not have one for trailers (seems odd) so I should take it to a paint shop. Sigh.
leoslaton is offline   Reply With Quote
Old 10-01-2010, 06:38 PM   #6
Jaycojenni
Junior Member
 
Join Date: May 2010
Location: Saginaw, MI
Posts: 28
Our Jayco dealer ordered the new "tin" as they refer to it and i'm guessing/hoping it is the same color as the rest of the trailer. If not i quess we'll be having a talk. But they didn't mention having to do any painting.etc.. I was at the dealer the other day and they were just getting started with it, only had the trim off but none of the tin. I have to tell you that makes one sick to see their trailer ripped apart. I hope it goes back together well and looks as it did before. Good luck with your repair. Did they give a you a cost estimate? Ours was just under $1000. to replace one piece of tin
Jaycojenni is offline   Reply With Quote
Old 10-02-2010, 01:03 PM   #7
leoslaton
Junior Member
 
Join Date: Aug 2010
Posts: 22
No, no estimate only that labor alone would exceed 30 hours. After that I didn't need a cost estimate.
leoslaton is offline   Reply With Quote
Old 10-02-2010, 02:09 PM   #8
Jaycojenni
Junior Member
 
Join Date: May 2010
Location: Saginaw, MI
Posts: 28
Ouch!
It looks like our labor was around 8 hrs and it would cost about $760 the one piece of seven ft of tin was $19.39, other shop supplies (sealants screws tape etc...)$35 and get this one............$125 for shipping and handling. I think i could of drove my suburban down from MI to IN and it would of cost less to bring back a seven ft piece of metal!


When we had our pop-up (starcraft) it was fiberglass and there was a crack in the roof, the dealer patched it and had a airbrush guy from the local auto dealer (Chevy l believe) i don't know what the cost of that was but the rv dealer cover it because the trailer was still under warranty. Of coarse your boo-boo on the trailer looks like it would need much more paint than a airbrush guy would do...
Jaycojenni is offline   Reply With Quote
Old 10-02-2010, 03:47 PM   #9
SmokerBill
Senior Member
 
SmokerBill's Avatar
 
Join Date: Sep 2010
Posts: 530
How about having a couple pieces of aluminum diamond plate cut out and attach it over the boo boo? Put one on each side so it looks like it's supposed to be there.
__________________
Bill
2011 Dodge Ram 1500 HEMI Quad Cab
2011 Jay Flight 26BH
SmokerBill is offline   Reply With Quote
Old 10-03-2010, 08:33 AM   #10
kipper
Senior Member
 
kipper's Avatar
 
Join Date: Jan 2010
Location: South Eastern Pa
Posts: 173
What I would do is a tube of clear paintable caulk , match the paint the best you can and fix it myself . It may not be the best repair job but it wouldnt look to bad . The last time I took our trailer to the dealer I was'nt impressed with their work any way ,
__________________

__________________
Kipper
If everyone is thinking alike, then somebody isn't thinking.
George S. Patton
kipper is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Powered by vBadvanced CMPS v3.2.3

All times are GMT -6. The time now is 10:59 PM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2014, vBulletin Solutions, Inc.