|
|
07-12-2016, 03:12 PM
|
#1
|
Junior Member
Join Date: Jul 2016
Location: Rushville
Posts: 6
|
Newbie to both forum and camping
Hi All....I am a Newbie to both this forum and camping...so be gentle please.
We just bought a nice condition 2006 23B...loved the layout and so far have been on two outings...all seems pretty good. a few questions though.
This weekend we seemed to develop a sulpher smell in the hot water...only when using the electric heat. I did some research and seems there may be microbes that emit this smell when the water is hot...so I will attempt a chlorine flush of the system. any idea what mixture chlorine to water?.. I figure to put 12 gallons of the mixture in the FW tank then pump it through and let it sit for a day, then flush loads of fresh clean water.
second Q....I see the pop-outs are vinyl covered canvas, and they are in great shape and do not leak...however, I have an inkling I should weatherproof them somehow...I am in the marine industry and familiar with what we use there on sunbrella products...but this is not sunbrella...its vinyl covered...any help here...I have searched the forum and am awfully confused as to the proper procedure.
looking forward to the camping lifestyle and the help..
Thanks all
|
|
|
07-12-2016, 03:22 PM
|
#2
|
Senior Member
Join Date: Jun 2012
Location: Southern Indiana
Posts: 1,326
|
Welcome PYG to the friendliest RV forum on the 'net! I found this article about sanitizing water systems and it gives the chlorine to water ratio.
The RV Forum
Enjoy your new to you X23B. We really like ours. As far as canvas care goes, you can use Pop-Up Gizmos, or PUGs as they are called. A lot of folks seem to like 'em.
PopupGizmos
__________________
2017 Some Other Brand (SOB)
2013 Jayco Jay Feather X23B (She Gone)
2014 Ford Expedition
Gerard
|
|
|
07-13-2016, 05:15 PM
|
#3
|
Junior Member
Join Date: Jul 2016
Location: Rushville
Posts: 6
|
Thank you
Thank you GL...that link was very helpful...flushed out with bleach yesterday and fresh water today...
3-4 weeks till our next camping trip so we will see if that does the job
|
|
|
07-13-2016, 07:56 PM
|
#4
|
Senior Member
Join Date: Nov 2014
Location: Trussville, Al
Posts: 2,093
|
Welcome aboard, you've found the right forum
__________________
Ron, Barbara & rescues Beamer (Lab mix), Buddy (Cavalier spaniel), Ruger (Golden retriever), Stanley (Bassett/Springer mix) and 3 grandsons
2012 Jayco Feather 29L BH
2015 Chevy 2500 HD Duramax and Equalizer WDH
|
|
|
07-14-2016, 08:56 PM
|
#5
|
Member
Join Date: Apr 2016
Location: Sherwood Park
Posts: 38
|
Manual '06 Lites
Also, in case your trailer's previous owner misplaced the manual, you can download one at the address below! Happy Camping!
http://www.jayco.com/files/downloads...ilename_98.pdf
__________________
2009 Jayco 19H
2014 Jeep Grand Cherokee V8
|
|
|
07-15-2016, 04:09 AM
|
#6
|
Senior Member
Join Date: Nov 2013
Location: Duxbury
Posts: 7,113
|
Congratulations on the new to you TT and welcome!
__________________
Rob & Kelly, Bella & Brady (Miniature Schnauzers)
2022 Eagle HT 28.5RSTS
2017 RAM 3500 SRW CTD/AISIN CC LB
|
|
|
07-15-2016, 05:12 AM
|
#7
|
Senior Member
Join Date: Mar 2015
Location: Abingdon
Posts: 6,177
|
Congrats and welcome!!!
__________________
2013 Jayco Eagle 328 RLTS
2021 Keystone Montana 3121RL
2013 F350 6.7L 4x4 CCLB
W/Air Lift air bags (front & rear)
Equal-I-Zer™ WDH & B&W Companion
|
|
|
07-15-2016, 05:19 AM
|
#8
|
Senior Member
Join Date: Jul 2015
Location: Mid-Mi
Posts: 1,492
|
Welcome and congrats on the first rig!!!
I have noticed that before, but the next trip is fine. It seems sometimes it may be the water itself if you had a fresh water hook up.
Have fun!!!
|
|
|
07-15-2016, 09:44 PM
|
#9
|
Junior Member
Join Date: Jul 2016
Location: Rushville
Posts: 6
|
Thanks
Thank to all the well-wishers...this looks like its gonna be a fun ride!
Anyone have any advise on front mounts for bikes...I don't like the idea of mounting them on the back, and I have a trailblazer so putting them in the bed is not possible. I have heard of some mounts you can get that bolt onto the frame and put them above the propane tanks...but have yet to locate manufacturers.
|
|
|
07-16-2016, 06:12 AM
|
#10
|
Senior Member
Join Date: Feb 2016
Location: West Virginia
Posts: 306
|
Just in case, you should have a look at your heating element in the water heater. When they start to corrode and go bad they start to give off a sulphur smell in the water. Just a thought for something to look into.
__________________
2016 Jayco North Point 375 BHFS
2015 Chevrolet Silverado 2500 HD Duramax SB SRW
|
|
|
07-20-2016, 05:10 PM
|
#11
|
Member
Join Date: Nov 2015
Location: Washington
Posts: 87
|
Hello and welcome to the forums. Lots of friendly advice here. It could be that your location was on a well. We have family in Eastern Washington and Idaho who are on well water and every time we visit and take showers it always smells like rotten eggs. It's harmless and is only present when the water is hot.
Hydrogen Sulfide – Wellowner.org
__________________
Jake
2016 Ford F150 XLT 2.7 EcoBoost
2016 Jay Feather X17Z
Tekonsha P3 Brake Controller
EAZ-Lift Weight Distribution Hitch w/Sway Control
|
|
|
07-20-2016, 06:08 PM
|
#12
|
Senior Member
Join Date: Jan 2015
Location: Surprise
Posts: 2,623
|
You may want to check and see if you have an anode rod in your hot water tank. If so it is part of the drain plug and if partially eroded you may want to replace it.
Welcome and Enjoy your new to you TT.
__________________
2011 Toyota Tundra double cab
2015 27RLS
|
|
|
07-20-2016, 08:05 PM
|
#13
|
Junior Member
Join Date: Jul 2016
Location: Rushville
Posts: 6
|
No anode as I have an Atwood heater...and I did check with the campsite...the water was city water and did not smell in the camps showers so I am sure it was an issue with my unit.
I sanitized everything, yet to try it out but will in the next few days
|
|
|
05-19-2017, 07:59 AM
|
#14
|
Senior Member
Join Date: Apr 2017
Location: Victoria
Posts: 172
|
We bought a Jack It A frame bike rack. Works great!
|
|
|
05-20-2017, 04:30 PM
|
#15
|
Member
Join Date: May 2017
Location: Northeast
Posts: 39
|
Following for the front bike mount question!
|
|
|
05-20-2017, 04:33 PM
|
#16
|
Member
Join Date: May 2017
Location: Northeast
Posts: 39
|
Quote:
Originally Posted by MagooIsBoo
We bought a Jack It A frame bike rack. Works great!
|
Does that fold down or remove easily to allow the front bed on the TT to fold down?
|
|
|
05-22-2017, 10:38 PM
|
#17
|
Senior Member
Join Date: Apr 2017
Location: Victoria
Posts: 172
|
Hi, on our hybrid with the Jack It bike rack, we do have to take off the top part of the rack, (if you look at a pic of the rack with bikes on it, it is the part which the bikes actually rest on) which is quite simple to remove with one quick release clip in order to get the bed down, but the main mounting post of the rack stays attached to the A frame of the trailer. There is about two inches of clearance from the bike rack main mounting post to the underside of the bed when it is down. I'll see if I can find a pic online for you. We already put the trailer to bed from this weekend. Here is an online image.
https://www.google.ca/imgres?imgurl=...act=mrc&uact=8
|
|
|
05-22-2017, 11:00 PM
|
#18
|
Member
Join Date: Oct 2015
Location: Bullhead City
Posts: 45
|
WELCOME Enjoy your ntu camper.
__________________
Jim and Bea
2000 Coleman Bayside Elite (Sold)
2009 Jayco Feather Export 17c
2012 Nissan Titan
Pee Wee, Razzie and Jack
|
|
|
05-23-2017, 02:41 PM
|
#19
|
Member
Join Date: May 2017
Location: Northeast
Posts: 39
|
Quote:
Originally Posted by MagooIsBoo
Hi, on our hybrid with the Jack It bike rack, we do have to take off the top part of the rack, (if you look at a pic of the rack with bikes on it, it is the part which the bikes actually rest on) which is quite simple to remove with one quick release clip in order to get the bed down, but the main mounting post of the rack stays attached to the A frame of the trailer. There is about two inches of clearance from the bike rack main mounting post to the underside of the bed when it is down. I'll see if I can find a pic online for you. We already put the trailer to bed from this weekend. Here is an online image.
https://www.google.ca/imgres?imgurl=...act=mrc&uact=8
|
Thanks! It also looks like you have to use their electric jack...is that correct?
|
|
|
05-23-2017, 06:15 PM
|
#20
|
Senior Member
Join Date: Apr 2017
Location: Victoria
Posts: 172
|
Hi, no we are still able to use our original jack. My hubby did have to remove the original jack to place the bike mount on, but then screwed everything right back together. It was a little finicky to do by himself, a second set of hands would have been helpful to screw and hold things together, but entirely doable on his own.
One helpful piece of advice is to set the cradle hooks and the mount pins for the tires with the Y frame on the ground first. Trying to adjust the cradle mounts with the bikes while the frame is in the air is awkward.
|
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|