Jayco RV Owners Forum
 


Reply
 
Thread Tools Display Modes
 
Old 09-10-2016, 02:19 PM   #1
Senior Member
 
Join Date: Aug 2015
Location: Apple Valley
Posts: 172
Scan D install

I am having a problem plugging the 9 pin connector into the diagnostic connector. Any tricks? I line everything up and push hard but it's acting like the pins are to big to fit in. Don't want to bust it
__________________

Mnwelsh is offline   Reply With Quote
Old 09-10-2016, 04:37 PM   #2
Senior Member
 
Robbbyr's Avatar
 
Join Date: Dec 2014
Location: Akron
Posts: 1,198
My ScanGauge connection has two ways (sides) it can plug in, make sure you are using the correct side!
__________________

__________________
Rob R.
Akron, OH
2014 Seneca 37TS
Toads: 2014 Ford Explorer Sport or 2013 Ford Focus ST
Robbbyr is offline   Reply With Quote
Old 09-11-2016, 03:16 PM   #3
Senior Member
 
Join Date: Aug 2015
Location: Cincinnati
Posts: 176
just installed and it plugs right in.
__________________
Mike
2015 Seneca HJ
mikew968 is offline   Reply With Quote
Old 09-11-2016, 03:40 PM   #4
Senior Member
 
Join Date: Aug 2015
Location: Apple Valley
Posts: 172
Thanks for the information. The pins were very tight but I finally got it on. It would fall off with the slightest pull. Put some tie wraps on it to secure the connection and it works perfect.
__________________
Mnwelsh
Apple Valley MN
2015 Seneca TS
Previous RVs: 3 truck campers and 2 fifth wheels
Love the Seneca. Toad Jeep Unlimited
Mnwelsh is offline   Reply With Quote
Old 09-11-2016, 04:01 PM   #5
Senior Member
 
Join Date: Aug 2015
Location: Carencro
Posts: 152
Installed

I ran my cable up the A pillar and made a small bracket that hangs just below the small overhead bin. Ill add a picture in a bit.
__________________
Terry
N5QWA
2014 Jayco Seneca 37FS
tjbroussard is offline   Reply With Quote
Old 09-11-2016, 08:22 PM   #6
Member
 
Join Date: May 2016
Location: Aransas Pass
Posts: 46
Would like to see your mount. I've got my tire minder up there already next to the overhead bin so was wondering about a place for the Scan gauge assuming I find value in it. I honestly think Trans temp might make it worthwhile but was looking for more "support".
BrentJ is offline   Reply With Quote
Old 09-11-2016, 08:26 PM   #7
Senior Member
 
Join Date: Aug 2015
Location: Carencro
Posts: 152
here you go. Aluminum angle stock.


Sent from my iPhone using Tapatalk
__________________
Terry
N5QWA
2014 Jayco Seneca 37FS
tjbroussard is offline   Reply With Quote
Old 09-11-2016, 08:26 PM   #8
Senior Member
 
Join Date: Aug 2015
Location: Carencro
Posts: 152



Sent from my iPhone using Tapatalk
__________________
Terry
N5QWA
2014 Jayco Seneca 37FS
tjbroussard is offline   Reply With Quote
Old 09-11-2016, 08:58 PM   #9
Member
 
Join Date: May 2016
Location: Aransas Pass
Posts: 46
Did you fasten the angle to the bin or some of the metal behind the bin?
BrentJ is offline   Reply With Quote
Old 09-12-2016, 03:49 AM   #10
Senior Member
 
Join Date: Aug 2015
Location: Carencro
Posts: 152
Simple auto adhesive tape to the underside of the bin and on the gauge. Snaked the wire from behind and made a small notch on edge of headliner to accomodate the cable.
__________________

__________________
Terry
N5QWA
2014 Jayco Seneca 37FS
tjbroussard is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Virginia State Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3

All times are GMT -6. The time now is 02:39 AM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Copyright 2002-2016 Social Knowledge, LLC All Rights Reserved.