|
09-08-2018, 03:09 PM
|
#1
|
Senior Member
Join Date: Jan 2018
Location: Harlingen
Posts: 257
|
Seneca jacks
Can anyone tell me what to check first, my jacks won't come down. They had been working great until last night and were still two months from home.
2017 38rb
Thanks
|
|
|
09-08-2018, 06:55 PM
|
#2
|
Junior Member
Join Date: May 2015
Location: alma
Posts: 12
|
I am certainly not an expert but;
check for blown fuse or tripped breaker
check fluid level in hydraulic tank, could be low?
Are batteries weak? Let them charge a little
Is the touch pad flashing any odd lights? Check your manual for the Leveling system you have.
|
|
|
09-08-2018, 07:13 PM
|
#3
|
Senior Member
Join Date: Jan 2017
Location: Manchester Center
Posts: 1,519
|
Do your stairs work? If not check the circuit breaker on the chassis batteries. There is a knife switch that supplies power to jacks and steps. Be sure ignition is off, check your grounds they have a habit of falling off.
__________________
Paul
2018 37TS
Jeep JL
|
|
|
09-08-2018, 09:51 PM
|
#4
|
Member
Join Date: Nov 2017
Location: Waymart
Posts: 44
|
Check the breaker on your chassis batteries. Tripped on me once and messed with radio, levelers, and steps.
__________________
|
|
|
09-09-2018, 10:16 AM
|
#5
|
Senior Member
Join Date: Jan 2018
Location: Harlingen
Posts: 257
|
Thanks for all the advice. My steps work, can't find a problem with ground wires, Doesn't mean I missed one. So I'll ask this if my fluid level was low, it's hard to tell, would you still hear the pump run? I've got nothing going on except the lights all come on on the dash control panel.
|
|
|
09-10-2018, 08:29 AM
|
#6
|
Senior Member
Join Date: Sep 2017
Location: Anaheim, CA
Posts: 408
|
I would call Equalizer (if that’s the brand you have).
Hey have been extremely helpful when I reached out to them.
I’d also look up the manual and go through the troubleshooting section just in case it mentions something in there.
-
__________________
2018 Seneca 37RB
2005 LJ Rubicon - Sahara #90
2019 Can Am X3 XRS Max
2009 ATC enclosed trailer
|
|
|
09-10-2018, 10:42 AM
|
#7
|
Senior Member
Join Date: Oct 2017
Location: Oregon Coast
Posts: 3,097
|
There is a fuse holder wired inline right by the pump on mine, have you checked there?
__________________
Brian & Jeannie
2018.5 Seneca 37RB with to many mods to list
2015 Jeep JKU Rubicon
|
|
|
09-10-2018, 11:54 AM
|
#8
|
Senior Member
Join Date: Oct 2016
Location: Albuquerque
Posts: 357
|
Stupid question...the motor is not running right, or ignition on. The system will allow the jacks to come up with them on, but wont go down if it thinks the ignition is on.
__________________
2016 Seneca 37FS
DW+7 kids+2 dogs=bunkhouse required
|
|
|
09-10-2018, 03:49 PM
|
#9
|
Senior Member
Join Date: Jan 2018
Location: Harlingen
Posts: 257
|
No such thing as a stupid question. You are right. I have tried every imaginable from whats's normal, even started the truck and moved it a little. It's been working great for several months, then all of the sudden bam.
Thanks
|
|
|
09-11-2018, 12:02 AM
|
#10
|
Member
Join Date: Mar 2016
Location: Arlington
Posts: 45
|
Check your solenoid underneath your rig to be sure all the nuts are tight over your wires. Mine worked loose causing my system to not function but all the lights on the panel were lit. Mine was on the driver’s side mid way back on the inside of the rail. Seneca 37TS, not sure if all are the same.
__________________
2016 Jayco Seneca 37TS
Toad 2017 Jeep Wrangler Sahara
2013 Dutchman Voltage Toyhauler (gone)
2012 Ford F-350 Dually
|
|
|
09-11-2018, 12:14 AM
|
#11
|
Member
Join Date: Mar 2016
Location: Arlington
Posts: 45
|
Additionally, check my post from 3-6-18 for some pictures and more detail.
__________________
2016 Jayco Seneca 37TS
Toad 2017 Jeep Wrangler Sahara
2013 Dutchman Voltage Toyhauler (gone)
2012 Ford F-350 Dually
|
|
|
09-12-2018, 08:28 PM
|
#12
|
Senior Member
Join Date: Jan 2018
Location: Harlingen
Posts: 257
|
Well my jacks now work manually. I looked for loose wires and bad fuses. I did replace one fuse that was good because I had one. I hate it when something now works and you don't know why.
Thanks everyone for your help!
|
|
|
09-13-2018, 07:13 AM
|
#13
|
Senior Member
Join Date: Jan 2017
Location: Manchester Center
Posts: 1,519
|
Do they work manually but not automatically? There is a module located somewhere in your basement ceiling. This contains the actual level sensor. Verify that it is firmly attached to the ceiling. I would also check the wiring clips to be sure they are firmly set. Sometime a loose wire can be a pain to find and could cause poor function of a system like this.
__________________
Paul
2018 37TS
Jeep JL
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|