|
08-26-2014, 04:50 AM
|
#1
|
Junior Member
Join Date: Jul 2013
Posts: 21
|
Adjusting FW ride height using factory bolt positions
I've got a 2001 Designer that's riding nose-high. Can't lower the pin any lower. ETA: I didn't adjust the pin at all- I meant to say I can't adjust the pin because the camper is already at the proper height above the bed rails.
There are two more bolt positions where the leaf springs attach to the frame that could be used to raise it about 2 1/2 inches or maybe a tad more.
Any issues with doing this? Seems pretty straightforward.
Anyone ever done it?
|
|
|
08-26-2014, 05:14 AM
|
#2
|
Senior Member
Join Date: Jun 2014
Location: The Mitten
Posts: 459
|
You lowered the pin box or raised it? Is your hitch adjustable?
|
|
|
08-26-2014, 05:24 AM
|
#3
|
Junior Member
Join Date: Jul 2013
Posts: 21
|
I don't think the pin box needs adjustment because I don't want the front of the fifth wheel to be any closer to the bed rails than it already is.
The problem is the ride height at the rear of the coach, not the front.
|
|
|
08-26-2014, 05:52 AM
|
#4
|
Junior Member
Join Date: Jul 2013
Posts: 21
|
Up camper- I just realized why you asked the question... lowering the pin would raise the nose and that's what you thought I did... LOL
I didn't mess with the pin at all. It's where it needs to be already.
|
|
|
08-26-2014, 07:27 AM
|
#5
|
Senior Member
Join Date: Sep 2010
Location: New York
Posts: 2,210
|
Are your axles flipped, meaning the axles are under the leaf springs already? You probably can adjust the springs up in the holes provided, but you might want to check with Jayco Technicians on that first.
__________________
2014 375 BHFS Eagle Premier
2014 Ram 3500 Longhorn DRW CC
6.7 CTD, Aisin, 4.10's
Yamaha EF3000iSEB
|
|
|
08-26-2014, 11:14 AM
|
#6
|
Senior Member
Join Date: Dec 2011
Posts: 427
|
We changed the spring mounting to raise our fiver to a level position for towing after I contacted Jayco- They told me that is what the extra holes are for- It worked for us and we are unaware of any problems- JMHO- DD
__________________
Fulltiming since July 1, 1999 currently with a 2005 GMC Sierra 3500 cc drw towing a 2007 Jayco Eagle 341RLQS
|
|
|
08-26-2014, 01:09 PM
|
#7
|
Senior Member
Join Date: Dec 2010
Posts: 2,229
|
Since I had a 4wd truck when we ordered our Eagle, my dealer specified using the lowest mounting holes for the spring mounts from the factory. My trailer now rides ever so slightly nose down, perfect for towing and needs only to raise up an inch when overnighting while still hitched up on a level site.
__________________
2019 Airstream Flying Cloud 27FB
2012 321RLTS Eagle (sold)
2011 F350 CC SB
|
|
|
08-26-2014, 01:19 PM
|
#8
|
Junior Member
Join Date: May 2014
Location: south elgin
Posts: 26
|
I just dropped the springs to the bottom holes on the shackle, left the equalizer where it was for now. No change in trailer handling, it's much closer to level now. I will be moving the equalizer bar down to the bottom hole too, this should be near perfect level for my F350 4X4.
__________________
2001 7.3 PSD 4X4 CC DRW 2007 Designer 31RLS 5th
|
|
|
08-26-2014, 02:58 PM
|
#9
|
Senior Member
Join Date: Jun 2014
Location: The Mitten
Posts: 459
|
Interesting. My 29.5BHDS does ride slightly nose high and truck doesn't quite sag enough. I have a F350 4x4 as well. It doesn't really have enough pin weight I guess being a half ton design. Nevertheless I will have to see if I have some kind of adjustment holes on the springs to raise the back slightly. Everything seems to be within spec, but it would look better it I could raise the back end slightly.
|
|
|
08-27-2014, 06:54 PM
|
#10
|
Senior Member
Join Date: May 2014
Location: Bonney Lake
Posts: 226
|
Yup that is why the holes are there. It's a jayco thing. Other option is to flip the axle, spring on top of axle this is what I did.
|
|
|
08-27-2014, 07:43 PM
|
#11
|
Junior Member
Join Date: May 2014
Location: south elgin
Posts: 26
|
Quote:
Originally Posted by imjustdave
Yup that is why the holes are there. It's a jayco thing. Other option is to flip the axle, spring on top of axle this is what I did.
|
don't you need to rotate the backing plate, for the brakes 180* when you do this?
__________________
2001 7.3 PSD 4X4 CC DRW 2007 Designer 31RLS 5th
|
|
|
08-27-2014, 08:31 PM
|
#12
|
Senior Member
Join Date: May 2014
Location: Bonney Lake
Posts: 226
|
Quote:
Originally Posted by SLEEKCRAFTER
don't you need to rotate the backing plate, for the brakes 180* when you do this?
|
Nope....
If your thinking that you rotate the axle around so the spring perch is up VS down... you can't as the axle has a bow to it.
What you do is install new spring perches on the top side of the axle.
http://dexteraxle.com/over_under_conversion_kits
I welded mine but you don't have to and it didn't take too long. While I was there I did the flex equalizers and lubed pins.
http://dexteraxle.com/e_z_flex_equalizers
No ofiliation with Dexter by the way.. but they did treat me well price wise and guaranteed some parts a few times no big Q asked.
|
|
|
08-29-2014, 03:19 PM
|
#13
|
Junior Member
Join Date: Jul 2013
Posts: 21
|
Wow. This thing seems to have less rolling resistance. He said it had no grease in the bearings, so he replaced them. Maybe it's just my imagination- they weren't making any noise.
It's a lot more level too. Not quite all the way but it's close enough.
|
|
|
12-25-2014, 01:06 PM
|
#14
|
Member
Join Date: Nov 2014
Location: Daytona Beach
Posts: 66
|
Did you need any special tools to lower the spring mounting to the lower mounting hole and were you able to DIY.
__________________
2015 Silverado 2500HD LTZ Diesel
2015 Eagle HT 28.5 RSTS
|
|
|
12-25-2014, 02:09 PM
|
#15
|
Senior Member
Join Date: May 2014
Location: Bonney Lake
Posts: 226
|
Jack, hammer, wrenches blocking for safety... the only thing special or not obvious is the bolt has serrations that bight into the hole, so you loosen the nut and then you have to push the bolt out of the hole, so a C clamp, Ball joint remover or air hammer works well, VS just hammering away.
Once you put it back in if it is greased the grease holes go horizontal and you should press the bolt in the hole, Im sure running the nut down or hammer would do it but a Ball joint press works really well to seat the bolt in the hole if it is a virgin hole, I rented a ball joint puller from auto parts store.
this is very DIY.
|
|
|
01-18-2015, 12:19 PM
|
#16
|
Junior Member
Join Date: Jul 2013
Posts: 21
|
Quote:
Originally Posted by F14man
Did you need any special tools to lower the spring mounting to the lower mounting hole and were you able to DIY.
|
The guy said he had all kinds of issues doing this job. He said he didn't bill me for all the time he actually spent.
I wouldn't have attempted this myself.
If you are used to wrenching on cars, or your dad is a TV repairman and has a righteous set of tools, you might be able to DIY.
|
|
|
02-26-2015, 07:42 PM
|
#17
|
Senior Member
Join Date: May 2014
Location: Bonney Lake
Posts: 226
|
Moving the holes the springs attach to is simple any shop should be able to do it or home mechanic. Wrench jack hammer are the special tools required.
Moving the axle under the springs is not much more work with the right parts. But lots more blocking and a few extra hands would be good.
|
|
|
02-27-2015, 08:30 AM
|
#18
|
Senior Member
Join Date: Aug 2011
Location: Missouri City, The Republic of Texas
Posts: 5,063
|
Quote:
Originally Posted by UPCamper
Interesting. My 29.5BHDS does ride slightly nose high and truck doesn't quite sag enough. I have a F350 4x4 as well. It doesn't really have enough pin weight I guess being a half ton design. Nevertheless I will have to see if I have some kind of adjustment holes on the springs to raise the back slightly. Everything seems to be within spec, but it would look better it I could raise the back end slightly.
|
First time in history this has been said. You need a smaller truck.
__________________
Cheers,
T_
2013 F-350 CC SB 2WD 6.7PS
2013 Eagle Premier 351 RLTS
-SOLD- 2012 X23B
-SOLD- 2003 Ford Expedition 5.4, Bilstein shocks
|
|
|
03-03-2015, 12:45 PM
|
#19
|
Junior Member
Join Date: Dec 2014
Location: Indianapolis
Posts: 13
|
Thanks everyone
Thanks. This thread is exactly what I have been looking for. My 2010 Designer sits a little too much tail down on my 2010 F350 4x4. I've been fretting over how to level things out. Too much snow right now to crawl under the trailer & look. I hope it's as you guys have described in the suspension. It'll solve my problem.
__________________
Darlene & Gary
Jayco Designer 35rlsa
F350 CC 6.4 SRW Cabelas, superglide
kayaks, bikes, fun
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|