|
10-05-2014, 01:09 PM
|
#1
|
Junior Member
Join Date: Oct 2014
Location: Graytown
Posts: 17
|
Winterizing a 2007 Jayco Eagle
When I winterize my 2007 Jayco Eagle, I know I am not supposed to put antifreeze through the water heater. And I know that somewhere there are three valves on the water heater or close to it, (A) Inlet, (B) Outlet and (C) Bypass. Problem is, I can't find these valves anywhere. I can see the water heater when I remove a small wood panel inside from the furnace wall of the storage area on the right side (nearest the water heater). I also see a yellow valve handle but thats it. I want to bypass the water heater before adding antifreeze so as not to put any in the water heater.
Can anyone help me in locating these 3 valves?
|
|
|
10-05-2014, 01:16 PM
|
#2
|
Lost in the Woods
Join Date: Jun 2014
Location: Woodstock
Posts: 1,128
|
They would be directly behind the Heater.
Why are you sure you have them? Many pups don't
Did you just buy it?
If you take a pic and post it we could confirm 100 percent
|
|
|
10-05-2014, 01:30 PM
|
#3
|
Junior Member
Join Date: Oct 2014
Location: Graytown
Posts: 17
|
I just bought it in August from an individual. It was sitting on a campsite and we are just going to leave it there. We moved back home today because of the temperatures but are going back early next week to clean out the food, bedding, etc. Will take pictures then and post them.
I'm not a newbie to piping and valves being an ex-boiler operator and instructor in the Navy back in the 70's but I just don't see them.
Thanks for the reply!
|
|
|
10-05-2014, 01:58 PM
|
#5
|
Junior Member
Join Date: Oct 2014
Location: Graytown
Posts: 17
|
Jayco Technical Support says there is and they stressed not to allow any antifreeze into the water heater. They couldn't tell me the exact location of the valves but said they were there.
I'll have to investigate more!
|
|
|
10-07-2014, 07:19 AM
|
#6
|
Senior Member
Join Date: Jan 2011
Location: Vienna
Posts: 2,044
|
Sometimes a panel has to be removed from the inside, and sometimes there is an adjacent storage area inside or outside that will allow you to access water heater. If you can see the pipes going into and out of the water heater and there is not another pipe in the middle connecting the two, with valves on all three, then it does not have the bypass feature. I would think that a 2007 would have this feature.
__________________
Joe Hinson
2010 Jayco Quest G2(SOLD)
2014 Jayco Eagle 33.5RETS
2007 Ram 2500 5.9L Cummins(SOLD)
2015 Ram 2500 6.7L Cummins 4WD
:)
|
|
|
10-07-2014, 10:59 AM
|
#7
|
Senior Member
Join Date: May 2013
Location: Pohatcong
Posts: 216
|
I just winterized mine last weekend filled water heater before I shut the valves off. Will antifreeze damage the water heater? Should I pull plug and flush with water. Thanks and not trying to hijack his thread
|
|
|
10-07-2014, 11:04 AM
|
#8
|
Lost in the Woods
Join Date: Jun 2014
Location: Woodstock
Posts: 1,128
|
Quote:
Originally Posted by chrisb
I just winterized mine last weekend filled water heater before I shut the valves off. Will antifreeze damage the water heater? Should I pull plug and flush with water. Thanks and not trying to hijack his thread
|
no it will not harm the heater
Just a waste of antifreeze
I would drain it and collect it and reuse it next year perhaps or dump it in your grey and black tanks at least
|
|
|
10-07-2014, 06:16 PM
|
#9
|
Senior Member
Join Date: May 2013
Location: Pohatcong
Posts: 216
|
Thanks, thought I may have caused a problem
|
|
|
10-07-2014, 06:43 PM
|
#10
|
Junior Member
Join Date: Oct 2014
Location: Graytown
Posts: 17
|
To totally fill the water heater would take about 7 gallons of antifreeze. I would just as soon bypass mine and save some $$$ on antifreeze. Am going to try and find the in, out and bypass valves tomorrow.
|
|
|
10-07-2014, 06:45 PM
|
#11
|
Junior Member
Join Date: Oct 2014
Location: Graytown
Posts: 17
|
Do the inlet and outlet pipes go into and out of the top of the heater? I can see the heater but it's wrapped in thick styrofoam insulation.
|
|
|
10-07-2014, 06:46 PM
|
#12
|
Lost in the Woods
Join Date: Jun 2014
Location: Woodstock
Posts: 1,128
|
the cold goes in the bottom usually and the hot out the top
|
|
|
10-12-2014, 05:06 PM
|
#13
|
Junior Member
Join Date: Oct 2014
Location: Graytown
Posts: 17
|
I removed a small panel and I can see the water heater. There is also a small yellow vlalve handle at the bottom and at the top, there is a gray round thing. It appears to be a handle but doesn't turn. I did not find an outlet or a bypass valve and I'm not sure what the yellow one does.
These are the best pics I could get
|
|
|
04-18-2016, 03:30 PM
|
#14
|
Junior Member
Join Date: Oct 2014
Location: Graytown
Posts: 17
|
Ok, here is another issue for no hot water at the faucets. I am posting a picture of my Atwood 6 gallon LP Gas/Electric water heater. This picture is one that I got off the web but looks just like mine which is all hooked up.
The water enters at the lower left just before the ball valve with the yellow handle. Above, there appears to be another valve with a plastic knob on it. What does the upper valve do. Should I have closed or opened it (not knowing it's position now) when I turned on my water after winter storage?
The yellow handle should be inline with the valve for normal use and perpendicular when winterizing. This is per a sticker on the side of the water heater. When I put it in line, I get no hot water. And the tank is full of hot water when I can confirm.
This upper valve has me puzzled, if it's a valve.
TIA
JimmyT
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|