|
07-30-2013, 09:49 PM
|
#1
|
Junior Member
Join Date: Jul 2013
Location: Winnipeg, MB
Posts: 12
|
Calling all 1206 owners
Ok I have a question for all 1206 owners. On the inside of the exterior wall of my dinette I have two L brackets mounted just below the tent (see photos). Does anyone else have these, and what are these for??
By the quality of the installation I thought these may have been installed by the previous owner.
__________________
2007 J Series 1206
2010 Exploer Sporttrac Adrenalin
|
|
|
07-31-2013, 11:34 AM
|
#2
|
Senior Member
Join Date: May 2013
Location: Gurnee, IL
Posts: 1,307
|
I'll take a look at mine tonight to see if I have those as well. We are getting ready for a weekend getaway without the kids this weekend so I have to open it up anyway. Can't help you with what they are for though.
__________________
Scott, DW, and Identical Twin DS (12)
2022 Chevrolet Silverado 1500 LTZ Crew Cab 3.0L Duramax 4WD
2019 Jayco Jay Flight SLX 298BH
2013 Jayco Jay 1206 (Sold)
|
|
|
08-03-2013, 10:46 AM
|
#3
|
Junior Member
Join Date: Jun 2013
Posts: 4
|
Quote:
Originally Posted by Hammer_2012
Ok I have a question for all 1206 owners. On the inside of the exterior wall of my dinette I have two L brackets mounted just below the tent (see photos). Does anyone else have these, and what are these for??
By the quality of the installation I thought these may have been installed by the previous owner. <img src="http://www.jaycoowners.com/attachment.php?attachmentid=10564"/>
<img src="http://www.jaycoowners.com/attachment.php?attachmentid=10565"/>
|
We have these and they seem to guide and give the king bed rails some support in the down position. I usually watch from the door while DH pushes the bed in and these things are helping support those rails which are pretty long.
|
|
|
08-03-2013, 10:48 AM
|
#4
|
Junior Member
Join Date: Jun 2013
Posts: 4
|
We have these. They serve as support and guidance for the king size bed rails as they are pushed in, and then they rest on them while popped down. Probably just because those rails are pretty long.
|
|
|
08-03-2013, 02:14 PM
|
#5
|
Junior Member
Join Date: Jul 2013
Location: Winnipeg, MB
Posts: 12
|
Calling all 1206 owners
Cool thanks for the input!
__________________
2007 J Series 1206
2010 Exploer Sporttrac Adrenalin
|
|
|
08-05-2013, 05:21 AM
|
#6
|
Senior Member
Join Date: May 2013
Location: Gurnee, IL
Posts: 1,307
|
I took a look at my trailer this weekend as well. I also have them and I also think they support the front slide rails.
__________________
Scott, DW, and Identical Twin DS (12)
2022 Chevrolet Silverado 1500 LTZ Crew Cab 3.0L Duramax 4WD
2019 Jayco Jay Flight SLX 298BH
2013 Jayco Jay 1206 (Sold)
|
|
|
09-08-2013, 03:01 PM
|
#7
|
Junior Member
Join Date: Jun 2012
Posts: 1
|
Hammer's question has been answered, but I was just curious if he was able to tighten the screws in the brackets or if he, or anyone else, has had to adjust the way these are attached, relocate them, or do any other modification.
I am the third owner of my 1206 and the screw holes in the wood for these brackets are stripped out and the brackets won't stay in place. While oversized screws would have the necessary diameter, the diameter I need would have a length that may penetrate the exterior.
I was thinking of replacing the two brackets with aluminum angle that is continuous from one bracket attachment point to the other and attaching with screws 6" to 8" on center. That way I cover the old holes in the paneling and presumably attach to fresh wood behind the paneling, making a more secure connection. This would also give my bunk rail a little more room to slide as well as support as it appears to be bent downward a little and I think was hitting the brackets and eventually knocked them loose.
I assume there is a continuous piece of wood across the top of the paneling/sill of the canvas to support the studs behind the paneling as well as the top of the interior paneling and exterior sideing. Can anyone confirm this framing assumption to be true?
Originally, I was planning to remove the paneling and reinforce the studs so I could put the brackets back in their original location, but that would involve removing the dinette seats and storage, and detaching the canvas and trim work.
Thanks, Hammer, for posting this thread. I am not trying to hijack it, but it appears that your brackets were loose as my were before I removed them, so am trying to find a solution.
|
|
|
09-10-2013, 11:11 AM
|
#8
|
Member
Join Date: Sep 2013
Location: Austin
Posts: 68
|
I recently removed and reattached my brackets because they were loose and causing the king slide rails to jam. I moved the position of the brackets slightly to get fresh wood and used some square drive screws of an appropriate length. You could also consider making some small thin blocks and attaching the blocks to the wall, then the brackets to the blocks..
If you do move the brackets, make sure to test closing the king bed carefully to test the alignment. The rail on mine drooped a little, so the farther bracket needed to be slightly lower than the close one.
__________________
1995 Toyota 4Runner SR5 4WD 5 spd
2002 Eagle Summit 12
|
|
|
09-10-2013, 04:07 PM
|
#9
|
Member
Join Date: May 2012
Location: Minneapolis, mn
Posts: 72
|
They are antenna that are utilized with the optional short wave radio. Lol. Appears you got your answer. Happy camping
__________________
JayKo 141
Minneapolis, Mn
TV: Any Chevy will do
2005 Jayco 1007 - 2007 - 2012
2010 Jayko 141J - 2012 -
|
|
|
09-18-2013, 08:26 PM
|
#10
|
Member
Join Date: Sep 2013
Location: Austin
Posts: 68
|
A little follow up for you all.. I went back today (since I was loading up) and had a look. I took a photo of my brackets' current position, and did a little tapping / pressing to see if I could find solid wood. There seemed to be at least a little bit of real wood behind the paneling, but it was offset and only by the leftmost bracket. So it seems to me that each pop up is probably different, but if you just knock on different parts of the paneling, or try pressing on it gently, you'll see where's solid and where's not.
You can see in this photo as I mentioned before, that I put the second bracket a skosh lower to prevent the rails from jamming.
Tomorrow bright and early I'm off to Port Aransas!
__________________
1995 Toyota 4Runner SR5 4WD 5 spd
2002 Eagle Summit 12
|
|
|
11-12-2013, 10:02 PM
|
#11
|
Junior Member
Join Date: Oct 2013
Posts: 2
|
Stripped Screw in Wood Repair
I've had good luck fixing stripped wood screws by taking a drywall knife and peeling off a sliver of pine (from a 2X4 or whatever) the size of the hole or a little larger. I coat the sliver of wood with Liquid Nails construction adhesive and press it into the stripped hole, trimming any excess flush with the surface that you're repairing. I usually install the screw while the adhesive is still wet and am careful not to re-strip the hole. As the screw goes in, it spreads the "plug" even wider and tighter in the hole and the adhesive, once dry, bonds to both the wood and screw. A pilot hole may have to be drilled first, depending on the size of the screw. I would guess the repair to be stronger than the undamaged surrounding wood.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|