Buying an Eagle 321RSTS

[RoadrunnerII]

Originally Posted by Fyrehuntr

You need to go camping, sit back [emoji482], and enjoy all the hard work you have put in. But, if you’re like me, that will last until you see something else you want to tinker with!



I’m curious, what did tying in the One Control router to your router do for you?

I tied it in or rather changed the one control router to a bridge. It's a wired connection so no lose of wireless signal. I also mounted a plastic restraint to hold the one control router antenna strait up rather that sideways. My phone would switch from my Asus router to the one control and I would not have an internet connection. It had a WiFi connection so it would drop the data connection from the cell side. The end effect was no email, and no browsing.

Now wife and I can wander out front or back and retain my WiFi. So a little bigger circle of coverage. My asus router is mounted behind the big tv in the kitchen slide. One control router is slightly higher and midship on trailer above the closet.
I also made sure to set them at different channels. Asus has a hard drive with movies on it and a VPN setup on it.
We are camping this week. Using a ubiquiti ap to the campground wifi.
With this setup I only have to setup the ubiquiti when we change campgrounds. Not my phone, wife's phone, tablet and smart tv.
Not doing any streaming on it just email, browsing internet, Tapatalk, wife for Facebook etc.
When down south I have a hotspot I connect to the asus router instead of the ubiquiti ap and use an unlimited data plan.
Yeh I am a retired IT geek
Gotta keep the brain and hands busy

RoadrunnerII

[Big1]

Pick up my new 2018 3500 CTD today.

[videoguy]

Originally Posted by TxLoser

Installed the Sony 2.1 System and Blue-ray today. Had to carefully drill into the Sony sound-bar to make It fit the existing bracket. The wireless sub fits snug behind the theatre seats. This 10 year old system sounds worlds better than the Furrion. Thanks for the suggestion.

Do you have a power outlet for the sub behind the theater seat? My 28.5rsts did but this one doesn’t which is why I put behind the tv.

[TxLoser]

There’s an outlet between the table and right side theatre seat. Behind the table chair if you can picture that. The sub is actually behind that seat. Any bigger and it wouldn’t fit.

[videoguy]

We opted for the dinette vs the table and chairs so maybe that’s why I didn’t find it. I’ll have to look closer, maybe it’s in the dinette wall next to the theater seat. Thanks!

[AKRUEBBE]

Originally Posted by Big1

Pick up my new 2018 3500 CTD today.

Super nice rig Big1

[Big1]

Oh yeah thank you I'm almost up there with you now, with the big boys. 😁

[JFlightRisk]

Big, that truck is sweet. But I kinda have a thing for red trucks.

[Big1]

Originally Posted by JFlightRisk

Big, that truck is sweet. But I kinda have a thing for red trucks.

Lol, yeah me too I had a 2006,2011,2014,2016,2017 and this one 2018 and all of them have been flame red. Thank you but I think this one I will keep it for a long time.

[TxLoser]

That truck looks great. Looking forward to hearing your impressions towing with this vs the 3/4.

[RoadrunnerII]

Originally Posted by Big1

Lol, yeah me too I had a 2006,2011,2014,2016,2017 and this one 2018 and all of them have been flame red. Thank you but I think this one I will keep it for a long time.

Nice looking truck Big1
I'm sure you will find it pulls your trailer effortlessly! Can't argue on the Cummins engine.

RoadrunnerII

[Big1]

Originally Posted by RoadrunnerII

Nice looking truck Big1
I'm sure you will find it pulls your trailer effortlessly! Can't argue on the Cummins engine.

RoadrunnerII

Yes sir and I just can't wait the next time that we will be going out is around the first week of September, bummer but I will go out to hook it up to my new B&W Companion puck hitch and the new truck and then I will be able to see how much it sag. Thanks again for your comment and I will post pics when I hook it up.

[Fyrehuntr]

Thought I would post a pic of my travel magnet mod. Didn't want magnets on the fridge.

[Big1]

That is a great place to put those at, I think that you have some more to add, lol.

[SB_James]

Originally Posted by Fyrehuntr

Thought I would post a pic of my travel magnet mod. Didn't want magnets on the fridge.

Very cool idea! Did you cut the sheet metal yourself? I’m totally going to do this hack when we get our rig!

[Fyrehuntr]

Originally Posted by SB_James

Very cool idea! Did you cut the sheet metal yourself? I’m totally going to do this hack when we get our rig!

Just went to a local HVAC installer with measurements. Had them roll the leading edge so no sharp edges were exposed. The edges around the remainder of the perimeter are flat cut. You can run a dremel down the edge if you want to remove sharp edge. Used velcro command strips to mount to wall.

When mounting sheet metal in place:
Place bottom edge in first
Place one hand behind middle of panel and bend/warp slightly while moving top edge into place
This will make sure neither top nor bottom sharp edges scratch any surface.

[vrader]

Hi All, despite the rather lengthy list of warranty issues I'll be dealing with for some time (which is disappointing but I expect Jayco to stay behind their product and workmanship) we love the trailer.

Shortly after the 1st couple of uses the front slide "shudders" when about 1/2 way extended and also on the way back in, like something is dragging. I don't see anything obvious and since this only occurs 1/2 way I don't it has anything to do with the motors so I'm left thinking it has something to do with the way the slide is mounted and maybe something came loose such that when the weight shifts to the outside something now rubs and shakes??

Any ideas or similar experiences??
Thanks,
Victor

[Big1]

Originally Posted by vrader

Hi All, despite the rather lengthy list of warranty issues I'll be dealing with for some time (which is disappointing but I expect Jayco to stay behind their product and workmanship) we love the trailer.

Shortly after the 1st couple of uses the front slide "shudders" when about 1/2 way extended and also on the way back in, like something is dragging. I don't see anything obvious and since this only occurs 1/2 way I don't it has anything to do with the motors so I'm left thinking it has something to do with the way the slide is mounted and maybe something came loose such that when the weight shifts to the outside something now rubs and shakes??

Any ideas or similar experiences??
Thanks,
Victor

Wow, that's not good so do the dealer have it now or are you waiting to take it in? So sorry you are having so much trouble and yes I would keep up on Jayco. Do you think that if you can put some lube on the gears and slide will make a different? Please keep us posted.

[Big1]

I did some update on my new 3500, my bakflip came in today.

[TxLoser]

Looks good. What kind of tires are those?