|
|
02-17-2020, 01:42 PM
|
#1
|
Senior Member
Join Date: Aug 2014
Location: San Antonio
Posts: 115
|
Atwood Nylon Plug
Just got back from a quick camping trip and the plug won’t come out. Drilled out the middle and still won’t come out. Took a chisel to it and it still won’t come out. I think it melted into the threads. Any suggestions?
|
|
|
02-17-2020, 01:48 PM
|
#2
|
Member
Join Date: Feb 2020
Location: Grand Rapids
Posts: 57
|
interesting. never heard of this, but, if so, you'll just have to keep digging the remains out of the water heater. replace with a metal plug when done.
|
|
|
02-17-2020, 02:10 PM
|
#3
|
Senior Member
Join Date: Nov 2011
Location: Where ever the boss says we're going.
Posts: 16,111
|
Quote:
Originally Posted by Spur
I think it melted into the threads.
|
Nylon's melting point is over 500 degrees, sounds like it cross threaded when you put it in.
__________________
DISNEY LOVERS
|
|
|
02-17-2020, 02:27 PM
|
#4
|
Senior Member
Join Date: May 2013
Location: SE Wisconsin
Posts: 3,431
|
Drill out the hole big enough to fit a hack saw blade or cross cut hand saw. Then cut it. Be careful not to be too aggressive to damage the threads. But a couple of cuts, even if not all the way through should let you break it apart to get it out.
__________________
Chuck
2013 Jayco Jayfeather X20 E (sold)
2016 Chevy Silverado LTZ 2 Z71 Crew Cab (sold, and dearly missed)
|
|
|
02-17-2020, 02:52 PM
|
#5
|
Senior Member
Join Date: Aug 2014
Location: San Antonio
Posts: 115
|
I couldn’t get a saw in there because the space is so tight. Tried sawing it with a drywall saw with little success. Finally lost my temper and chiseled it out of there with a screw driver. The last wack sent the plug into the tank! I guess I can’t use the heater anymore?
I did some damage to the threads. I had two replacement plugs that, had I not just went through what I just went through, I would have been disappointed because they fit so tight. Anyway, I filled up the tank and the new plug didn’t leak so I guess I’m good.
|
|
|
02-17-2020, 02:55 PM
|
#6
|
Senior Member
Join Date: Aug 2014
Location: San Antonio
Posts: 115
|
Quote:
Originally Posted by Grumpy
Nylon's melting point is over 500 degrees, sounds like it cross threaded when you put it in.
|
I hand tightened it down before I put a socket to it. I must have been distracted because that plug was tightened all the way down! Can I use the heater now that I have a mangled plug inside the tank?
|
|
|
02-17-2020, 02:59 PM
|
#7
|
Lost in the Woods
Join Date: Apr 2019
Location: Ocean County
Posts: 2,807
|
Could be a good time to consider what some of us have done, put in a nylon nipple with a short piece of braided water line and drain valve, so you won't have to unscrew the plug to drain each time.
|
|
|
02-17-2020, 03:09 PM
|
#8
|
Senior Member
Join Date: Aug 2014
Location: San Antonio
Posts: 115
|
Quote:
Originally Posted by RetiredOne
Could be a good time to consider what some of us have done, put in a nylon nipple with a short piece of braided water line and drain valve, so you won't have to unscrew the plug to drain each time.
|
Do you have some instructions or a video that would show me how to do it?
|
|
|
02-17-2020, 03:10 PM
|
#9
|
Senior Member
Join Date: Dec 2012
Location: Southern Indiana
Posts: 3,209
|
Quote:
Originally Posted by Spur
Can I use the heater now that I have a mangled plug inside the tank?
|
Probably but it may clog the outlet flow. Also if you have an electric side to the water heater the plastic plug could be melted to it. We had a member who had a plastic flush out tip get stuck inside and he drained his tank, removed the electric element which provided a larger hole, and fished it out with a pair of hemostats, I believe. Good luck.
__________________
2012 Eagle 320 RLDS
2017 Ford F-250 FX4 Crew STX 6.2l
3.73 E-locker
|
|
|
02-17-2020, 03:25 PM
|
#10
|
Senior Member
Join Date: Feb 2017
Location: Dallas
Posts: 4,281
|
Quote:
Originally Posted by RetiredOne
Could be a good time to consider what some of us have done, put in a nylon nipple with a short piece of braided water line and drain valve, so you won't have to unscrew the plug to drain each time.
|
That's an awesome idea thanks!
__________________
Tight Lines and accurate shots
|
|
|
02-17-2020, 03:42 PM
|
#11
|
Lost in the Woods
Join Date: Apr 2019
Location: Ocean County
Posts: 2,807
|
Quote:
Originally Posted by Spur
Do you have some instructions or a video that would show me how to do it?
|
Here's a picture of what I did to mine. Got a 1/2 nylon nipple from Amazon, and the braided water line and valve from Home Depot.
I drain down the water heater after every trip, I don't want the water to ferment in the tank between trips.
|
|
|
02-17-2020, 04:02 PM
|
#12
|
Senior Member
Join Date: May 2018
Location: Colorado
Posts: 778
|
Quote:
Originally Posted by Spur
Just got back from a quick camping trip and the plug won’t come out. Drilled out the middle and still won’t come out. Took a chisel to it and it still won’t come out. I think it melted into the threads. Any suggestions?
|
If that happens again to someone, take a can of compressed air, turn it upside down and freeze the plug. It’ll shrink and should easily come out.
__________________
JOHN
People Sleep Peacefully in Their Beds at Night Only Because Rough Men Stand Ready to Do Violence on Their Behalf
|
|
|
02-17-2020, 04:11 PM
|
#13
|
Senior Member
Join Date: Feb 2017
Location: Dallas
Posts: 4,281
|
Quote:
Originally Posted by RetiredOne
Here's a picture of what I did to mine. Got a 1/2 nylon nipple from Amazon, and the braided water line and valve from Home Depot.
I drain down the water heater after every trip, I don't want the water to ferment in the tank between trips.
|
I like that thanks for sharing.
__________________
Tight Lines and accurate shots
|
|
|
02-17-2020, 04:47 PM
|
#14
|
Lost in the Woods
Join Date: Apr 2019
Location: Ocean County
Posts: 2,807
|
Quote:
Originally Posted by Woodworker
I like that thanks for sharing.
|
I wish I could say that was my original idea, but I learned it from other guys here!
The first time I tried to take out that plug told me there has to be a better way.
|
|
|
02-17-2020, 07:26 PM
|
#15
|
Senior Member
Join Date: Nov 2016
Location: Port Huron, Mi
Posts: 1,737
|
I took my gas burner out, pretty easy to do, and used a close nipple and a ball valve and threaded it right in. Reinstalled the burner and life is much better. Now all I do is thread a long plastic nipple into the ball valve and let er rip. Works great. It keeps the water from running all down the cover and destroying the stickers on the inside of the door and no more tools needed to drain the tank. I cant remember if I got the parts from Depot or Lowes, but it was one of them.
Sorry the pic is sideways.
|
|
|
02-17-2020, 08:42 PM
|
#18
|
Lost in the Woods
Join Date: Apr 2019
Location: Ocean County
Posts: 2,807
|
Quote:
Originally Posted by Spur
I hand tightened it down before I put a socket to it. I must have been distracted because that plug was tightened all the way down!
|
I think there is a lesson to be learned for everyone. The nylon plug DOESN'T have to be tightened all the way down.
I know it's easy to do, since it's plastic and doesn't have much resistance, but in reality, since water pressure is only in the 40 - 60 psi ranges, best method is to put some telfon tape on the plug, and when it's snuggly tightened with your fingers, maybe one extra full revolution or so with a wrench is all that's needed to keep it from leaking. There's no reason to crank it completely in.
|
|
|
02-17-2020, 08:51 PM
|
#19
|
Senior Member
Join Date: Aug 2014
Location: San Antonio
Posts: 115
|
Quote:
Originally Posted by RetiredOne
I think there is a lesson to be learned for everyone. The nylon plug DOESN'T have to be tightened all the way down.
I know it's easy to do, since it's plastic and doesn't have much resistance, but in reality, since water pressure is only in the 40 - 60 psi ranges, best method is to put some telfon tape on the plug, and when it's snuggly tightened with your fingers, maybe one extra full revolution or so with a wrench is all that's needed to keep it from leaking. There's no reason to crank it completely in.
|
Amen
|
|
|
02-17-2020, 08:56 PM
|
#20
|
Senior Member
Join Date: Aug 2014
Location: San Antonio
Posts: 115
|
Quote:
Originally Posted by ggilbert
|
I was looking for this before I started hammering on things! Would I need the 1/2 inch or the 3/4?
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|